How To Repair Insoles In Shoes

Download Article

Download Commodity

Soles are often the beginning part of a shoe to wear out. Fortunately, every bit long as the balance of the shoe is in good shape, repairing the sole can be an easy style to brand your shoes good as new. With a little sandpaper and some shoe sole adhesive, you lot can replace worn-out soles or prepare holes or loose soles in simply a few minutes, and wear them again within 24 hours.

1
Pull the old sole off with pliers. Even if the sole is starting to come loose, you will probably need pliers to pull it off the shoe entirely. Concord the shoe firmly and pull on the edge of the sole with pliers, moving the sole abroad from the lesser of the shoe. If the sole doesn't come off easily, try wedging a paint scraper or butterknife betwixt the sole and the shoe every bit yous pull on the sole with pliers.^[i]
- You lot can also employ a oestrus gun or hair dryer to warm up the mucilage that attaches the sole, which will make information technology easier to remove.
2

Clean off any old glue using acetone. There may yet be some stale glue remnants on the lesser of your shoe where the sole was attached. Cascade a little acetone or smash shine remover on a rag and scrub the bottom of your shoe with it. The glue should dissolve and scrub off. Make clean whatsoever clay or residual grime off the shoe too.^[2]

Advertizing
iii

Roughen up the lesser of the shoe and the new sole with sandpaper. Rough surfaces hold together better with glue than smooth ones. Utilize 120-grit sandpaper to scratch up the bottom of the shoe and the top of the sole until their textures appear rougher.^[three]
4
Apply shoe sole adhesive to the new sole with a castor or cotton ball. Follow the instructions on the adhesive for application. Some adhesives must sit for a few minutes, or "cure," before the item can be put in place. Some adhesives require heat to be activated
- Shoe Goo is a common and effective shoe sole adhesive, and is available in many shoe shops, sports supply outlets, and department stores.
v

Put the new sole in place and printing it tightly against the shoe. If the adhesive needs to cure before information technology'due south used, wait for as long equally the instructions point earlier putting the sole on. Beginning at the front and lay the sole gradually on the shoe, making certain the edges line up properly. Once information technology's in place, use pressure level to stick information technology firmly on the bottom of the shoe.
6
Clench the sole to the shoe using rubber bands, duct tape, or weights. The sole needs to be pressed tightly confronting the shoe for the two surfaces to adhere. Secure the sole in place by wrapping rubber bands or duct record around the shoe, or by placing information technology on the ground and setting weights on acme of it to printing the shoe into the sole.^[4]
- Information technology can exist helpful to stuff the shoe with paper first and so that information technology keeps its shape while existence clamped.
vii

Wait 24 hours before using the shoe again. Virtually shoe sole adhesives take at least a full twenty-four hours to set. Allow your shoe sit down somewhere cool and dry where information technology's not in danger of being moved or touched.^[v]

Advertizement

one

Clean the shoe and sole with water and alcohol. Use a rag to rub some warm water and isopropyl booze over the area effectually the loose part of the sole. If you can exercise and so without pulling it off further, clean within where the sole has become loose as well.
two
Apply shoe sole adhesive between the shoe and the sole. Use a toothpick or cotton swab to apply a layer of adhesive inside where the sole has come apart from the shoe. Make the layer fairly thick, as it's improve to put in too much and take it overflow than to not have plenty.^[6]
- Some adhesives need to cure for a few minutes after beingness applied and before the sole is put in place. Check the instructions on your agglutinative production.
iii

Printing the sole confronting the bottom of the shoe. Being careful not to become any agglutinative on your easily, press the sole and the shoe together tightly. Don't worry if some adhesive spills out -- this tin can be sanded off afterward.
4

Continue the sole in place with condom bands, duct tape, or weights. The sole should be pressed tightly against the shoe for the unabridged fourth dimension it dries. Secure information technology using safety bands or duct tape, or prepare weights on meridian of the shoe in the surface area where the mucilage is drying.^[seven]
5

Let the shoe sit for 24 hours. Place the shoe somewhere out of the mode, where it can stay cool and dry while information technology sets. Wait at least a full day before wearing the shoe.^[eight]
vi

Sand off any dried overflow glue. If any of the shoe sole agglutinative spilled out when you pressed the sole down, sand it off using 120-dust sandpaper. Make certain the adhesive has stale out completely earlier sanding it.^[ix]

Advert

one

Clean the expanse around the hole with h2o and booze. Use a rag to rub warm water and isopropyl booze around the hole to make clean off any dirt or crud. Let it dry out for a few minutes before continuing.
2

Roughen upwardly the edges of the hole with 120-grit sandpaper. This will help the glue adhere to the rubber. Scrub the edges of the hole with sandpaper until it appears to take on a rougher texture.^[10]
iii

Put duct tape over the inside of the shoe above the hole. Remove the insole of the shoe and place a piece of duct tape within the shoe where the pigsty is. If the hole does non go all the way through the inside of the shoe, put your finger in the hole and button upwards to see where the hole is and encompass that office with duct tape.^[11]
4

Fill the hole with shoe sole adhesive. Being careful not to touch the adhesive with your bare easily, gently squeeze it into the hole. Make sure the entire pigsty is filled, and don't worry if there is some overflow.
five

Use an ice cube to shine the surface of the adhesive. The ice cube will allow yous to polish the surface of the glue without sticking to it. You can besides use a tongue depressor or spoon covered with petroleum jelly.^[12]
6

Let the shoe dry for 24 hours with the sole turned up. Set the shoe so that the sole is facing upwardly. Go out information technology somewhere out of the fashion where it will be cool and dry. Leave it for at to the lowest degree a full day.
seven

Sand down whatsoever dried agglutinative that overflowed from the hole. Check to encounter if there is stale glue protruding from the hole or spilling out over the edges. If there is, utilise 120-grit sandpaper to sand it downwards until the lesser of the sole is smooth.^[13]

Add New Question

Question

What should I bank check before I repair or replace my soles?

Rio Jongsae Kim is a Designer Shoe and Bag Repair Specialist and the Owner of Kim's Shoe & Purse Repair in Vancouver, BC, Canada. With over 40 years of experience, Rio and Kim'south Shoe & Bag Repair specialize in the repair and reconstruction of leather and luxury appurtenances including shoes, handbags, and accessories. Rio's feel and dedication to quality repair and restoration take led to his work beingness featured on Yahoo, Insider, and MSN.

Designer Shoe & Bag Care Specialist

Skillful Respond

You have to check to see if the soles have started to thin, or they accept holes. You should also cheque both shoes to see if they're wearing away evenly, or if they're splitting from the upper side of the shoes.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

To avoid getting adhesive on your skin, vesture disposable gloves when applying the agglutinative or handling the shoe after you've glued information technology.

Nearly This Article

Article Summary X

If you need to repair a shoe sole, showtime by cleaning all over the shoe with a mixture of warm water and isopropyl alcohol and then the adhesive will stick. In one case the shoe has dried, use a toothpick or cotton fiber swab to apply a thick layer of agglutinative where the sole has come up apart from the shoe. Then, press the sole against the lesser of the shoe tightly, making certain not to go any adhesive on your hands. Don't worry if the adhesive spills out of the cracks, you tin can always sand information technology off later on. Since you desire the shoe and sole pressed tightly together until the agglutinative dries, secure them together with rubber bands or tape. Afterwards waiting 24 hours, remove any rubber bands or record and sand off the overflow glue with 120-grit sandpaper. For more assist, like how to fix a hole in the sole of your shoe, read on.

Did this summary assistance you?

Thanks to all authors for creating a page that has been read 171,085 times.